SKU: 600-0003-00

The Check-Line® TSD-50 manual torque measuring screwdriver is designed for accurate measurement of application and removal torque of screws and fasteners. An LCD display measures bi-directional torque in real-time or peak modes.The TSD-50 displays torque in lb-in, cN-M and Kg-cm and has a measuring Range of 0.45 – 4.50 lb-inThe TSD has an measuring accuracy of ±2% CW / ±3% CCW of indicated and has 9 programmable setpoints that provide both an audible beep and green/red LED indicator for precision torque application

Features

  • Uses standard 1/4″ bits
  • Clockwise & Counter Clockwise Torque Measurement
  • 9 Programmable Target Torque Setpoints
  • Real time & Peak Torque Measurement
  • Display Units: lb-in, cN-M and Kg-cm

Complete Kit

The TSD is supplied as a complete kit including the torque screw driver, Phillips size 0 bit (2.1in / 55mm length), instruction manual, factory calibration cert and 1 AAA battery in a hard plastic carrying case.
 

Specifications

 Accuracy  Clockwise: ±2% Counterclockwise: ±3% (of indicated)
Guaranteed from 20-100% of capacity
 Presets  9 Programmable setpoints with both audible beep and Green/Red LED
 Memory  50 readings
 Presets  9 Programmable setpoints with both audible beep and Green/Red LED indicator
 Drive  1/4 Inch – 6.35 mm Hex
 Operating Modes  Peak / Track (real-time)
 Power Supply  1x AAA Battery (included)
 Working Time  12 hours continuous use
 Auto Off  Automatic power off after 5 minutes of non-use
 Operating Temp.  -10°C – 60°C
Storage Temp. -20°C – 70°C
Dimensions Length (without bit): 200mm / 8in
Diameter at largest point: 29.5mm / 1.16in
Weight 430g
Warranty 1 Year

TSD Quick Start Instructions

  1. Press C to power on screwdriver.
  2. Press U/S to select desired measuring unit.
  3. To select TRACK or PEAK mode press and hold the U/S key for 2 seconds, the display will show MODE, then press the up or down key to select between PEAK or TRACK mode (indicated by a small P or T in the bottom right corner of display). Then press the U/S key three times to confirm your selection and return to measurement mode.
  4. Use up and down arrow keys to enter target torque. If you are simply measuring and do not have a target adjust the setpoint to the highest value (maximum capacity of the screwdriver).

Note, when there is no torque applied the TSD will display the target value or previous reading.


 

01-201-5-16-torque-wrench
SKU: 707-01201-00 The Anritsu torque wrench is used for SMA, 3.5mm, 2.92mm (K), and 1.85mm (V) connectors. Anritsu provides two connector tools that make connecting and disconnecting tiny connectors more easily and surely accomplished. ...
01-203-13-16-torque-wrench
SKU: 707-01203-00 Anritsu torque wrench, for SMA, 3.5mm, 2.4mm, 2.92mm (K), and 1.85mm (V) connectors. Features 13/16″ Torque Wrench 8 in-lbs +/- 6% For standard SMA and 3.5 mm, 2.4mm, 2.92mm (K), and 1.85mm (V)...
01-204-stainless-steel-connector-wrench
SKU: 707-01204-00 This is a handy stainless steel connector wrench for standard SMA, 3.5 mm, and 2.4 mm connectors, and for the 2.92mm (K) Connector and 1.85mm (V) Connector.  
tsd-50-digital-torque-measuring-screwdriver
SKU: 600-0003-00 The Check-Line® TSD-50 manual torque measuring screwdriver is designed for accurate measurement of application and removal torque of screws and fasteners. An LCD display measures bi-directional torque in real-time...
­