Frequently Asked Questions
At Wild River Technology, we know that high-speed design and signal integrity challenges can raise a lot of questions. This FAQ section addresses the most common inquiries about our services, technologies, and processes—from test fixture design and VNA measurement to 3D modeling and simulation workflows. Whether you’re an engineer, program manager, or system architect, you’ll find helpful insights here.
Start by contacting Wild River Technology to discuss the design challenge, target data rate or frequency range, current test results, and project schedule. For a focused engagement, it is helpful to provide available PCB stack-up information, layout or interconnect geometry, simulation files, S-parameter data, TDR results, and applicable performance requirements. The team can then discuss [...]
Yes. Wild River Technology offers training on S-parameter workflows, VNA calibration, measurement setup, and verification. Training is available on-site or virtually, including remote demonstrations. This support can help engineering teams improve measurement repeatability, understand their measurement data, and integrate reliable S-parameter models into their electronic design automation (EDA) workflows.
Yes. Wild River Technology can design and build test vehicles tailored to a customer's technology roadmap. A test vehicle can help evaluate fabrication variables such as impedance, etch variation, and material properties, while providing structures for 3D electromagnetic modeling and measurement correlation. This gives engineering and fabrication teams objective data for validating manufacturing processes before [...]
The services include electromagnetic modeling of interconnects, vias, transmission lines, and RF connector launches, along with material identification and simulation-to-measurement correlation. Wild River Technology identifies Ansys HFSS and Cadence Clarity as tools used in its modeling workflows. Depending on the project, deliverables can include models, measurement comparisons, material identification reports, and supporting PCB libraries.
Can Wild River Technology characterize PCB materials for more accurate signal integrity simulations?
Yes. Wild River Technology offers a material identification service that uses dedicated test structures, precision measurements, and 3D electromagnetic simulation to characterize PCB dielectric properties. The process can determine dielectric constant (Dk) and dissipation factor (Df) in the X, Y, and Z directions, helping engineers account for material anisotropy. The program includes pre-fabrication modeling and [...]
An RF connector launch can contribute significant reflections and frequency-dependent loss to a high-speed measurement or serial link. Wild River Technology uses 3D electromagnetic modeling and measurement validation to optimize launch geometry for specific application goals. For serial link characterization, the optimization can account for the intended data rate and coding; for de-embedding applications, broadband [...]
Wild River Technology develops test fixtures around the application's electrical requirements, operating frequency, connector configuration, and measurement objectives. Its services include high-speed signal integrity fixtures, ATE device interface boards, SERDES characterization platforms, backplane fixtures, and RF connector launch optimization. The company describes fixture capabilities extending to 110 GHz, with the actual validated performance dependent on [...]
Yes. Wild River Technology lists emergency engineering and redesign among its signal integrity services. This support is intended for urgent engineering problems, including failing or non-compliant designs. The team can evaluate the immediate technical challenge and determine an appropriate path toward diagnosis and corrective action. Availability and turnaround depend on the project's scope and should [...]
Yes. Wild River Technology offers SI analysis and debugging services that use simulation, TDR measurements, S-parameter analysis, and root-cause diagnostics to investigate electrical failures. Depending on the problem, the work may include examining impedance discontinuities, excessive channel loss, crosstalk, connector launches, PCB stack-up assumptions, and discrepancies between simulated and measured results.
Wild River Technology provides signal integrity modeling, analysis, and debugging; emergency engineering and redesign; 3D electromagnetic modeling; custom test fixture design and validation; RF connector launch optimization; precision VNA measurements; and PCB design and fabrication support. These services help engineering teams identify electrical performance issues, validate designs, and improve high-speed system reliability.
Wild River Technology offers signal integrity modeling, analysis, and debugging; precision VNA and TDR measurements; RF connector launch optimization; high-frequency test fixture design and validation; and channel modeling platforms. These capabilities help engineers investigate difficult electrical problems, validate simulations against hardware, and improve confidence in high-speed designs. The best starting point is to define the [...]
Engineers can compare measured and simulated channel responses against the applicable electrical specifications and channel budgets. Relevant checks may include insertion loss, return loss, crosstalk, impedance, eye opening, and bit error rate (BER). Depending on the interface, compliance analysis may also use Channel Operating Margin (COM) or statistical link analysis. The appropriate limits depend on [...]
A connector launch transitions a signal between a coaxial connector and a PCB transmission line. Poor pad geometry, via placement, grounding, or impedance matching can introduce reflections and excess loss that compromise both system performance and measurement accuracy. Electromagnetic simulation followed by physical validation helps optimize the launch and improve measurement repeatability at high frequencies.
PAM4 encodes two bits per symbol using four distinct signal levels. Compared with binary NRZ signaling, the smaller voltage separation between adjacent levels makes the signal more sensitive to noise, distortion, and linearity errors. At high baud rates, channel loss, crosstalk, reflections, and equalizer performance all contribute to the challenge of maintaining acceptable bit error [...]
An eye diagram overlays many received signal waveforms to reveal timing and voltage variations. Eye opening indicates the available margin for reliably distinguishing symbols, while eye closure can indicate noise, jitter, intersymbol interference, crosstalk, or channel loss. Eye diagrams are useful for evaluating equalization strategies and diagnosing high-speed serial link problems.
Passivity means a passive network cannot generate net energy. Causality means its response cannot precede the stimulus that causes it. Models that violate these physical properties can produce misleading simulations or unstable time-domain behavior. Checking and, where appropriate, correcting S-parameter data helps ensure it is suitable for trustworthy channel analysis.
A channel modeling platform provides physical test structures, measurement data, and supporting models that engineers can use to validate electromagnetic simulations and material assumptions. Wild River Technology's CMP-50 and CMP-70 platforms support simulation-to-measurement workflows, with nominal frequency coverage up to 50 GHz and 70 GHz, respectively. Such platforms help teams establish more reliable design processes [...]
The dielectric constant influences a transmission line's propagation characteristics and impedance, while the dissipation factor contributes to dielectric loss. Real PCB materials can also exhibit frequency dependence and directional variation, known as anisotropy. Accurate material characterization helps engineers predict delay, impedance, and attenuation more reliably, particularly at very high frequencies and data rates.
Correlation establishes whether a simulation accurately predicts the behavior of a real, fabricated structure. Poor correlation can lead to incorrect design decisions and repeated board spins. Comparing measured and simulated S-parameters, TDR waveforms, and other responses helps engineers refine material properties, geometry, port definitions, and modeling assumptions.
Simulation predicts electrical performance using mathematical models of materials, geometries, components, and interconnects. Physical measurement captures the behavior of fabricated hardware. Simulation helps engineers evaluate designs before manufacturing, while measurement validates the actual result. Using both allows teams to identify modeling errors, manufacturing effects, and design problems that might otherwise remain hidden.
Fixture de-embedding mathematically removes the modeled or characterized electrical effects of test fixtures from a measurement, helping isolate the behavior of the device under test. It is important because connectors, launch structures, and PCB fixture traces can add loss and reflections that distort the results. Wild River Technology's technical resources cover methods such as Automatic [...]
Calibration corrects systematic measurement errors caused by the instrument, cables, and measurement interfaces up to defined reference planes. Without appropriate calibration, measured reflections and transmission can include errors that do not belong to the device under test. At high frequencies, careful calibration, stable connections, and repeatable test procedures are essential for trustworthy results.
S-parameters describe how signals enter and leave a network at defined ports, including reflections and transmission between ports. For example, S11 describes reflection at port 1, while S21 describes transmission from port 1 to port 2. Engineers use measured or simulated S-parameters to model channels, assess loss and matching, and predict high-speed link behavior.
A VNA measures the amplitude and phase of signals reflected from and transmitted through a device over a range of frequencies. These measurements are commonly represented as S-parameters. Engineers use VNAs to characterize insertion loss, return loss, coupling, and other high-frequency behaviors, producing data that can support accurate channel models and simulation.
Time-domain reflectometry (TDR) sends a fast electrical edge into a device or transmission line and measures reflected energy. The resulting waveform helps identify impedance changes, discontinuities, and their approximate locations. TDR is especially useful for validating PCB traces, vias, connector launches, and test fixtures. Wild River Technology offers TDR measurement and signal integrity services for [...]
Crosstalk occurs when electromagnetic fields from one signal path couple energy into another. It can result from closely spaced traces, poorly controlled return paths, connector coupling, or inadequate isolation between channels. Mitigation techniques include optimizing trace spacing and routing, improving reference-plane continuity, controlling connector geometry, and validating the design with electromagnetic simulation and measurement.
Insertion loss describes how much signal energy is lost as a signal travels through a channel. Return loss describes the signal energy reflected back toward the source because of impedance mismatches. Both matter: excessive insertion loss reduces the received signal, while poor return loss can introduce reflections and waveform distortion.
A SerDes channel is the complete electrical path between a serializer transmitter and a deserializer receiver. It may include IC packages, PCB traces, vias, connectors, cables, and backplanes. Its performance depends on insertion loss, return loss, crosstalk, impedance consistency, timing distortion, and the transmitter and receiver's equalization capabilities.
As data rates increase, the available timing and voltage margins shrink, while channel losses, reflections, crosstalk, and manufacturing variations become more consequential. PAM4 signaling also uses multiple voltage levels, making noise and distortion more significant relative to the distance between adjacent levels. Successful designs require better modeling, measurement, and control of the complete channel.
Signal integrity (SI) is the ability of an electrical signal to travel through an interconnect and arrive at its destination with sufficient timing accuracy, amplitude, and waveform quality for reliable operation. At high data rates, PCB traces, connectors, vias, packages, and cables behave as interconnected transmission lines. Their losses, impedance discontinuities, and coupling can distort [...]
"We're building a new family of systems—can you support a test vehicle build?" Yes, we can help you. We recommend 2 options, both of which WRT can help you with. Build a Test Vehicle (TV) suited to your technology roadmap that addresses issues of Fabrication validation (impedance, etch variation, etc.) 3D EM optimization of key [...]
"When should/shouldn't I use forward couplers for injecting crosstalk?" We don't recommend using forward couplers for injecting crosstalk into serial link systems. There are no forward couplers in backplane or general serial link systems. Generally, they are wideband systems with channel characteristics unlike PCB t-lines. True power spectral density of the crosstalk is impacted by [...]
"When should/shouldn't I use phase shifters for skew?" First of all, PCB skew is not phase shifter skew, which often has bandwidth issues. Phase shifters work well for simple narrow band carrier based signaling systems, but not broad-band digital systems. PCB skew, such as provided by our SKEW-112 platform, has following advantages over phase shifters: [...]
Wild River Technology helps teams accelerate their signal integrity capabilities through structured collaboration. We begin with an NDA and a prioritized review of current and next-gen SI challenges, offering consulting support tailored to your design and measurement needs.
Forward couplers fall short in SERDES testing, failing to replicate real PCB crosstalk. XTALK-56 offers a more accurate, loss-aware platform for evaluating true transmission impairments and jitter behavior.
Test platforms are not typically available for evaluation, but in select cases, Wild River Technology may consider it based on project needs. Contact Sales to inquire.
Use our website’s auto-quote feature. This eliminates the need for back-and-forth communication and lets you get pricing details quickly and efficiently. If you have further questions or need a formal proposal, our sales team is always available to help.

